What is 427A refrigerant?

What is 427A refrigerant?

Refrigerant R427A (sold under the name Forane) is an HFC mixture which is suitable to serve as a replacement gas in various R22 applications in low, medium and high temperature cooling and air conditioning units. In operation, the cooling power drops by about 5% but the efficiency improves by 5–10%.

Is 427A a drop in for R-22?

Forane® 427-A refrigerant is an ideal replacement for R-22 and has a much lower cost. 427A out performs other common R-22 retrofits in most applications and can be used in air conditioners, heat pumps and refrigeration applications.

Can you top off R-22 with 427A?

Can I mix Forane® 427A and R-22? Mixing refrigerants is not recommended as it creates a new refrigerant that is not EPA approved. In addition, it contaminates the R-22. Proper calculation of superheat and subcooling becomes extremely difficult, which could result in damaging the compressor.

What is 427A used for?

Forane® 427A Refrigerant (R-427A) was commercialized in 2005 to supply the growing demand in Europe for an R-22 retrofit. R-427A has a similar capacity, efficiency, and mass-flow rate to R-22, making it an easy retrofit option for large, medium, and small air-conditioning and refrigeration systems.

What type of oil is 427A?

Forane® 427A is a 100% HFC blend made of R-32, R-125, R-143a and R-134a. It does not contain any flammable hydrocarbons. It is consequently compatible with the elastomers and plastic materials usually compatible with R-407C and R-404A.

What oil does 427A use?

Forane® 427A is compatible with polyolester (POE) lubricants. However, one advantage to Forane® 427A. of original oil in the POE lubricant, making for a simplified retrofit procedure.

Can you use 427A with mineral oil?

Outstanding performance, similar to that of HCFC-22, can be achieved without a complete oil change, thanks to the high tolerance of Forane® 427A to residual original oil (mineral or alkylbenzene).

Can I mix R-22 with MO99?

No. Freon™ MO99 should not be used to top off R-22 systems. Mixing refrigerants is not recommended. R-22 should be recovered using appropriate equipment and managed according to U.S. EPA guidelines specified in Section 608 of the U.S. Clean Air Act.

Can shops mix refrigerants?

The bottom line on this is that it’s a big no-no. Mixing refrigerants is dangerous and can cause big problems in your AC system. In fact, if you have a contaminated system, some shops might not even be able to work on your vehicle.

What is 421A refrigerant?

Choice™ R-421A is a non-ozone depleting, long term replacement for R-22 refrigerant. Requires no modification to AC / HP systems and is compatible with MO, AB, or POE lubricants. The only 2 component blend to replace R-22 and is within 1% of R-22 temperature / pressures.

Can you mix 427A and 407C?

Forane® 427A is a 100% HFC blend and does not contain any flammable hydrocarbons. It is compatible with elastomers and plastics normally compatible with R-407C and R-404A. Forane® 427A is compatible with polyolester (POE) lubricants.

Is MO99 a drop in refrigerant?

Freon™ M099 is the closest match to R-22 operating pressures and mass flow rates when compared to other “no-oil change” replacements. The use of MO99 will minimize system component changes….MO99, MO-99, R438A, Drop-In R22 Replacement M099 Refrigerant.

Name Chemours D12860273 – Freon™ MO99 refrigerant (R438A) 25lb Cylinder
Country of Origin USA
Brand Isceon™
Refrigerant R-438a

What is 427A refrigerant used for?

Forane® 427-A refrigerant is an ideal replacement for R-22 and has a much lower cost. 427A out performs other common R-22 retrofits in most applications and can be used in air conditioners, heat pumps and refrigeration applications.

What is Forane® 427A (r427a)?

Forane® 427A (R427A) is the Easy RetrofitTM when it comes to retrofitting many R-22 applications, including air conditioning, heat pumps, and low- and medium-temperature refrigeration. Forane® 427A matches R-22 closely in terms of performances and operating pressures and was developed to minimize the work necessary during an R22 retrofit.

Can I use 427A instead of R22?