How do I access ATA 192?
Cisco ATA 191 and ATA 192
- Plug the ATA into your local network from the Network port.
- Plug a computer into the ethernet port of the ATA 192.
- Navigate to 192.168. 15.1 (By default this device is routing and has DHCP on for connections with the Ethernet port.
- Log in using admin/admin.
How do I find the IP address of my Cisco spa112?
At the voice prompt menu, enter 110 #. The phone will read back the IP address of the base, which can be entered into a browser to access the configuration. At the voice prompt menu, enter 210 #. The phone will read back the IP address of the base, which can be entered into a browser to access the configuration.
How do I reset my Cisco ATA 191?
ATA 191 and ATA 192 Top Panel
- System detects a factory reset. To perform a factory reset, press and hold the RESET button for about 10 seconds.
- A factory reset is performed successfully.
How do I access ATA?
In the ATA Center server, click the Microsoft ATA Console icon on the desktop or open a browser and browse to the ATA Console. You can also open a browser from either the ATA Center or the ATA Gateway and browse to the IP address you configured in the ATA Center installation for the ATA Console.
How do I factory reset my Nokia 190?
Dial the following IVR code using the phone keypad: 73738 (RESET) followed by the # key. The IVR will ask you to confirm by pressing the 1 on the phone keypad. You must hang-up the phone to commence the reboot sequence.
How do I connect to Cisco ATA?
Step 1 Connect the network cable to your network and to the NETWORK port on the ATA. Step 2 Connect the phone cable to the PHONE 1 port on the ATA and to your analog device (phone or fax machine). If connecting a fax machine, connect it directly to the ATA.
How do I log into Cisco ATA?
Enter this IP address into your browser 192.168. 15.1 to be prompted for login. Log in to the device using the default (case-sensitive) username (“admin”) and password (“admin”), and then click Log In.
How do I connect my office phone to the Internet?
Steps to connect your landline to Wi-Fi router
- Power off the router.
- Connect the Ethernet wire.
- Connect your router to PC.
- Connect the phone to your router.
- Turn On the modem and PC.
- Power on the router.
- Test your landline.
- Power off your device.
How do I reset my Cisco SPA 112?
To reset the device to the default factory configuration, there are two options: Dial **** and at the prompt dial 73738# and then press 1 to confirm. Locate the Reset Button on the back of the SPA112. Using a paperclip, or something of similar dimension, hold the button for 20 seconds, then release.
How do I Reboot my ATA?
Another way to do it is by pressing the Reset > Reboot button. Click the Reboot button to power cycle the ATA. When the warning message appears, read the information, and then click OK to reboot the ATA, or click Cancel to abandon the operation.
How do I power cycle the ATA?
Use the Administration > Reboot page to power cycle the ATA from the ATA web page. Another way to do it is by pressing the Reset > Reboot button. Click the Reboot button to power cycle the ATA.
How do I Reset my ATA drive to default settings?
Power down or restart the computer and enter the system BIOS. Change the ATA Drive setting back to ATA Mode, press enter to accept the change and restart the computer. Click Yes to the Warning about the detected mode change on the embedded ATA controller. The system will boot normally to the Modern App Start Menu.
How do I backup and restore the ATA configuration settings?
Use the Administration > Config Management pages to backup and restore the configuration settings for the ATA. Use the Administration > Config Management > Backup Configuration page to back up the ATA configuration settings to a file. You can then later restore these same settings to the ATA.