What does E01 F06 mean on a washing machine?
A Whirlpool washer error code E01/F06 indicates that the washer’s motor control unit (MCU) is having trouble communicating with the washer’s central control unit (CCU). In most cases, the issue is caused by a damaged MCU circuit, usually caused by an overload.
How do I fix Indesit F06 error?
Indesit error F06
- Check if there’s any laundry in the door.
- Put the laundry all the way in the drum.
- Close the door and restart the washing machine.
How do I fix error code F06?
How to Fix F06 on a Whirlpool Duet
- Touch “Pause/Cancel” twice to cancel the F06 error on the display.
- Plug the power cord back in and select a new wash cycle.
- Press “Pause/Cancel” twice again if the F06 error code resumes.
What does F06 mean on an Indesit washing machine?
Door lock fault Issue
F06 — Door lock fault. Issue: Washing Machines door cannot be opened or closed / when the door is closed the machine the programme will not start.
What does error code E01 mean?
If you see either E01 displayed or an LED light repeatedly flashes once between pauses, your machine has identified the problem: error code E01. This error code usually relates to problems with the door lock. (In some models error code E07 can also indicate a door lock issue.)
What does F06 error mean?
The “F06” fault code indicates a drive motor tachometer error. This means the control is unable to properly detect motor speed and the machine will shut down. If the failure occurs during high-speed spin, the door will unlock after 3 minutes. Possible Causes/Procedure: Unplug washer or disconnect the power supply.
What does F06 mean on Maytag washer?
The F06 is a drive motor tachometer failure which means the motor control is not able to see the motor is running. This can be a difficult problem to pin down, A technician will most likely be needed but there are some things you can do yourself if you like. Check the connections between the motor control and motor.
What does F06 mean on a washing machine?
F06 — Door lock fault. Issue: Washing Machines door cannot be opened or closed / when the door is closed the machine the programme will not start. Advice: If your washing machines door will not close, please check for any obstructions in the door lock.
How do I fix E01 error?
To cure the E01 door lock fault take the following steps:
- Switch off and unplug your machine.
- Check the door lock itself. (Sometimes the plug on the lock can melt.)
- Check the wiring to the door lock.
- Check the wiring to the control board from the door look.
How do I fix error code E01 on my Maytag washer?
An error code E01 F09 on the screen of your Maytag or Whirlpool Duet washing machine could indicate that you have a drainage issue….Dirty Drain Catch
- Lean the washer at a 45 degree to the wall.
- Unscrew the screws on the bottom front panel.
- Remove the drain cap.
- Clean the drain catch.
What does error code E01 F06 mean on Whirlpool washer?
When the error code e01 f06 shows on your washer’s digital display screen, it means there is no connection between the two boards where a signal indicating the start of a program and switch from one mode to another is transmitted. When this happens, your washing machine will stop working, bringing your entire laundry operation to a standstill.
What does F06 E01 mean on a Maytag maxima washer?
Maytag maxima washer error code f06 e01 If there are E01 and F06 fault codes on the screen, you are dealing with a poor connection between the main control board and the motor control board. The latter is mounted to the washer’s floor. The former is located under the top panel and collects about a hundred wires from all electronic components.
F06 — Door lock fault Issue: Washing Machines door cannot be opened or closed / when the door is closed the machine the programme will not start. Advice: If your washing machines door will not close, please check for any obstructions in the door lock.
What does error code F02 mean on washing machine?
F02 — Motor circuit fault Issue: Intermittent or no drum rotation during wash cycle. Advice: We recommend you call our customer service centre to book an engineer on: 0344 822 4224 F03 — Temperature sensing fault