How do you use Acryl 60?

Mixing Instructions The normal ratio of Acryl 60® to clean potable water is 1 part Acryl 60® to 3 parts of water (1:3). Where increased physical and chemical resistance are required, increase the Acryl 60® content in the mixing liquid to a 1:2 or 1:1 Acryl 60® to water ratio. Always mechanically mix.

Is Thoroseal still made?

​​​Thoro concrete and waterproofing products now a part of Master Builders Solutions.

What is Thoroseal used for?

Thoroseal® 550i is a ready-to-use polymer-modified cement-based coating. It is used to waterproof and protect concrete, mortar, and masonry surfaces requiring either positive- or negative-side waterproofing. Thoroseal® 550i can be applied by low-pressure spraying or hand troweling.

How do you apply Thoroseal waterproofing?

Brush it On Start at the top and work down. Use a tampico fiber brush to apply Super Thoroseal® in a thick coat, working the mixture into the pores of the surface for a good penetrating seal. Double back and use the brush to smooth out the material. Allow 12 hours between coats for drying time.

How do you mix Thoroseal?

Blend the powder into the mixing liquid using a slow- speed mortar mixer (400 – 600 rpm). Mix until a thick, batter-like consistency is obtained. Leave the THOROSEAL to stand for 5 – 10 minutes to allow full saturation to take place. Re-mix, adding a small quantity of liquid if required, to restore the consistency.

What does Acryl 60 do?

DESCRIPTION: MasterEmaco A 660 (Acryl 60) is an acrylic-polymer concentrate is diluted up to 3:1 and is then mixed with portland cement mortars, plasters, stucco, and concrete mixes. Acryl 60 improves the adhesion, cohesion, tensile, compressive, and flexural strengths of these cement-based materials.

Which is better Drylok or Thoroseal?

First, in terms of the quality of coatings, Thoroseal is a better choice. However, Drylok is simpler to apply. Also, Drylok has a greater vapor permeability. On the other hand, Thoroseal is more resistant to absorbing moisture.

Does Thoroseal come in colors?

Coverage will vary depending on surface texture and porosity. White and standard gray (this color is not uniform) Custom and landscape colors are available for 5,000 lbs (2,268 kg) minimum order.

Does Thoroseal breathe?

Breathable, prevents build-up of water vapor which causes blistering, flaking and peeling of paint films and other non breathing coatings. Can be painted with 100% acrylic paint.

How much Thoroseal do I need?

Maximum dilution ratio is 1 part Acryl 60® to 3 parts water. Approximately 6 quarts (5.7 L) of mixing liquid is needed per 50 lbs (22.7 kg) of Thoroseal® powder. Water demand may vary with ambient temperatures and humidity levels.

Can you plaster over Thoroseal?

Where finishing is likely to be delayed for some time, the THOROSEAL® SUPER should be sand-dashed immediately after application to aid adhesion. Do not use a Gypsum based plaster directly over THOROSEAL® SUPER.

What is MasterEmaco?

MasterEmaco A 660 (Acryl 60) is an acrylic-polymer concentrate is diluted up to 3:1 and is then mixed with portland cement mortars, plasters, stucco, and concrete mixes. Acryl 60 improves the adhesion, cohesion, tensile, compressive, and flexural strengths of these cement-based materials.

How do you mix acryl 60 and thoroseal?

blend of Acryl 60®diluted with water. Maximumdilution ratio is 1 part Acryl 60®to 3 parts water.Approximately 6 quarts of mixing liquid is neededper 50 lbs of Thoroseal®powder. Up to 2 additionalquarts of mixing liquid may be added when using as.

Can thoroseal be used in water-retaining structures?

Before specifying Thoroseal®for water-retainingstructures, conduct tests to determine waterquality. Thoroseal®is not intended forcontinuous contact with acid or sulfate-containing water. Very soft water will have anadverse effect on Thoroseal®.

What is thoroseal coating?

Thoroseal® is a Portland-cement- based coating for concrete and masonry that resists both positive and negative hydrostatic pressure. Polymer-modified with Acryl 60®, Thoroseal® creates a low- maintenance and highly durable waterproof barrier.

Can thoroseal be used with insulation board?

4. Thoroseal®can be covered with extrudedpolystyrene insulation board during the second coatapplication. The board must be fully coated withThoroseal®and embedded into the still-wet coatingalready in place on the walls. Exercise care whenplacing the coated board because it should not bemoved or slipped. Once placed, do not move theboard.