What screws should I use for chipboard flooring?

Chipboard screws – to fix down in place after you lay chipboard flooring use 60mm wood screws . You will need to use 5 screws evenly spaced across each joist so you can use as many as 30 screws per board.

Table of Contents

How long should floorboard screws be?

We would recommend 50mm screws. The reason for this is that you want to avoid hitting electrical cables that may be running under the floorboards. There are strict rules for electrical contractors as to what depth they should drill holes through joists.

Should chipboard flooring be screwed?

Whilst chipboard flooring can be nailed, it is notorious for working loose and squeaking so screwing them down is the preferred method of fixing and really doesn’t take long using a decent cordless driver. Expansion gaps should be left around the perimeter of the flooring to allow for temperature and humidity changes.

How do you screw down a chipboard floor?

Firstly, apply a continuous bead of adhesive to the joists and noggins on which the chipboard panels will be laid. Then lay a chipboard flooring panel down, adding a screw to the tongue at each tongue and groove joint, to secure it to the joist below.

How many screws are in a chipboard?

60mm wood screws are used for chipboard screws to fix down in place after laying flooring. To use as many as 30 screws per board, you need to use 5 screws evenly across each joist.

Does chipboard flooring have to join on a joist?

It’s not essential, but if you really want to do it, then it’s not going to do any harm. Just thought of another thing… mark out any pipe/cable runs as you go (even if they’re under the joists)…you never know when you want to get at them and it helps any future occupier (not your problem I know…).

What size are floor screws?

You’ll want the screw to go about an inch past the plywood into the joist or underlying layer beneath it. So if your subfloor is 3/4 of an inch thick, any screw about 1 3/4 inches long will do the trick. If the plywood subfloor you’re placing is 5/8 of an inch thick, you need a screw about 1 5/8 inches long.

What size screws squeaky floorboards?

The 3/4-inch-thick subfloor takes a 2-inch screw. A thicker subfloor takes a 3-inch screw. Use a heavy-duty drill to drive Phillips head wood screws through the subfloor into the floor joists. Drive the screws approximately 8 inches apart.

Is 18mm chipboard OK for flooring?

Chipboard flooring is available in 18mm and 22mm thicknesses, and the tongue & groove sheets are 2400m x 600mm (approx. 8′ x 2′) in size. The sheets use high-density particleboard and are suitable for both domestic and commercial flooring.

Why do chipboard floors creak?

The squeak can be caused by the boards rubbing against each other or rubbing against the joists, glue on the joists is sometimesd used at installation this helps as does replacing nails with screws [even ringshank nails cannot cope with the poor density of chipboard].

How many screws do I need for subfloor?

When securing OSB or plywood subflooring, you should use a screw every 8 inches along the floor joist or truss. So, you’ll need 12 screws down the 8-foot length of OSB or plywood. If your floor joists or trusses are 16 inches on center, you’ll need 48 screws per 4×8 sheet.

What size screws for 22mm P5 chipboard flooring?

What size screws for T&G chipboard flooring?

I plan on laying T&G, 22mm, P5 chipboard flooring soon and would like to know what type and size screws should be used. I have looked through the forum and some people recommend 2.5 or 3 times the thickness of the chipboard for length. Some people recommend no. 8 or no. 10 screws, but Screwfix only seem to supply up to no.6 size screws.

What is the best 22 chipboard flooring?

on new buid when we lay a 22mm boards its standard to glue the joints and glue the joists that they are layed upon this stops squeek noise and promotes a more solid job 22 chipboard is used as the stock flooring on most jobs without any problems the boards with a green tint to them are the best as these are water resistant to a certain degree

What screws to use to screw into floorboards?

248 Country: IMHO – any wood screw provided it has a smooth shank at least as long as the thickness of the floorboarding. 2 per board (plank) into every joist spaced approximately 1/4 of the width of the plank in from each edge. If you are using sheet flooring the space screws at 4 to 6 inch spacing into every joist.